Articles about

How To Ground a Television or Communications Antenna

How to Install an Earth Grounding and Bond for Communication Antenna: Guide for Grounding an Antenna System

How To Convert a 30 Amp 250 Volt Outlet to a 15 Amp 220 Volt Outlet

Can I Convert a 30 Amp 250 Volt Outlet to be used for a 15 Amp 220 Volt Outlet? The Process to follow for Converting a 220 Volt Circuit.

How to Stop Fluorescent Lights from Flickering

Solving the Problem of Flickering Light Fixtures: How to Stop Those Annoying Flickering Fluorescent Lights, The Main Causes of Flickering Fluorescent Lights and How to Fix Them

How To Fix Your 3-Way Switches

Common Problems with 3-Way Switches and How to Fix Them: Basic Wiring Method for 3Way Switches, 3-Wire Cable Connects the Switches, Easy to Understand 3 Way Switch Diagrams.

How to Wire a Bath Exhaust Fan and Light

Installing and Wiring a Bath Exhaust Fan and Light: Power Sources for a Bath Exhaust Fan and Light, Power From a GFCI Outlet, Junction Box Wiring.

Replacing a Light Fixture with a Ceiling Fan

How to Replace a Light Fixture with a Ceiling Fan: Guide for Wiring a Ceiling Fan, Common Problems When Wiring a Ceiling Fan.

Can I Use A Remote Control Switch For Lighting?

How to Wire a Remote Control for Light Fixtures: Installing a Control Module, Wiring the Control Devices, Security and Monitoring Options.

How To Install A 3-Way Motion Sensor Switch

How can I install a single pole motion sensor switch in place of an existing three-way switch? Wiring a 3 Way Motion Switch.

Wiring for Lutron and 3-Way Dimmer Switches

How easy would it be for me to replace dimmer switches? How to Wire Lutron Dimmer Switches and Standard 3Way Dimmer Switches.

Why CFL Light Bulbs Flicker

Remote Control Units May Cause CFL Bulb Flicker: CFL lamps must be compatible with the light fixture and controlling device or switch where the CFL light bulb will be installed – Double check your wiring connections just to make sure, however I have a light fixture that is controlled by a motion sensor and the lamps are CFL too, and the light flickers when it is supposed to be off as well.

GFCI Circuit Breaker and Wiring

How to Wire a GFCI Circuit Breaker: Does it matter where in the breaker box panel I insert a 20 amp GFCI 220Volt breaker?

Wiring a Hot Tub 50 AMP GFCI Circuit

How to Wire a Hot Tub Circuit: Electrical Codes and Details for Spa and Hot Tub Wiring. Essentials for your installation, including the required GFCI ground fault protection and circuit wire size.

Outlet Connection for a 240 Volt Log Splitter

How to Adapt a Dryer Circuit for a 240 Volt Log Splitter: Materials List and Instructions to use a dryer circuit to provide power for a 220 Volt Log Splitter.

Fluorescent Lighting Problem and Repair Checklist

How to Identify and Repair a Fluorescent Light Fixture: Troubleshooting Checklist for Repairing a Fluorescent Light Fixture

Wiring Two Power Sources for a Submersible Pump

How can I have two power sources connected to a single pump and control each separate power source? Control Options for a Wiring a Pump with Two Sources of Power.

What to do about Stray Electrical Voltage Readings

How to Identify the Source of Stray Voltage: Stray Electrical Voltage Readings Should be Identified and Corrected Right Away – Stray voltage is not normal and may originate from a faulty electrical or electronic component that could potentially become a serious shock hazard and cause damage to equipment.

« Previous Page — Next Page »

Electrical Tips

To Help You Wire it Right

The Safest Way to Test Electrical Devices and Identify Electric Wires!
The Non-Contact Electrical Tester

This is a testing tool that is a Non-contact tester that I use to easily Detect Voltage in Cables, Cords, Circuit Breakers, Lighting Fixtures, Switches, Outlets and Wires. Simply insert the end of the tester into an outlet, lamp socket, or hold the end of the tester against the wire you wish to test. Very handy and easy to use.

The Quickest Way to Check for Faulty Electrical Wiring!
The Plug-In Outlet Tester

This is great to troubleshoot a problem with outlet circuit wiring, is also used by most inspectors to test for power and check the polarity of circuit wiring.
It detects probable improper wiring conditions in standard 110-125 VAC outlets Provides 6 probable wiring conditions that are quick and easy to read for ultimate efficiency Lights indicate if wiring is correct and indicator light chart is included Tests standard 3-wire outlets UL Listed Light indicates if wiring is incorrect, Very handy and easy to use.

Strip Off Wire Insulation without Nicking and Damaging the Electric Wire!
The Wire Stripper and Wire Cutter

A wire stripping tool used to safely strip electrical wires. This handy tool has multiple uses: The wire gauges are shown on the side of the tool so you know which slot to use for stripping insulation. The end of the tool can be used to grip and bend wire which is handy for attaching wire onto the screw terminals of switches and outlets.

Recent Testimonials

I think your site offers the the clearest and best electrical information for homeowners I have ever seen on the net.You have given me confidence to do my own projects which I never had before. THANK YOU!
Paul, from Foxboro, Massachusetts

I wish I found this site earlier, it is by far the best electrical related resource I have found on the web.
George, from Scranton, Pennsylvania

I love this site for an office worker that does not know anything about electric wiring.
Bill, from New York City, New York

This site is so much better than the 3 books I just bought, I wish I came here first.
Collin, from Grand Rapids, Michigan

Thank you for answering my question.
I was able to get this done. This site is perfect. I am glad I found it. Please keep it going.
Mike, from Chicago, Illinois

Read more Comments

Leave a Comment

»How To Wire It RIGHT! «
Wire it with Confidence!
Fully Illustrated
Instant Download

Now You Can
Wire it like a Pro!

Residential Electrical Wiring

Learn Electrical Wiring
Instructional Electrical Wiring Videos

Home Electrical Wiring and Electrical Repairs

Please Note:
Unless otherwise posted, please refer to the following Guidelines when working on Electrical Projects:

Skill Level:
Intermediate to Advanced - Electrical Repairs and Circuit Wiring is Best Performed by a Certified Electrician or Licensed Electrical Contractor.

Electrical Tools Required:
Basic Electricians Pouch of Hand Tools, a Voltage Tester and a Multi Meter.

Estimated Time:
Depends on personal level experience, ability to work with tools, work with electrical wiring, and the available access to the project area.

Precaution:
Identify the project circuit, turn it OFF and Tag it with a Note before working with the wiring.

Important:
Modifying existing electrical circuits or installing additional electrical wiring should be done according to local and National Electrical Codes, with a permit and be inspected.