240 Volt Wiring for an Electric Dryer
How to Wire the Electric Dryer Circuit Wiring: Dedicated Electric Circuit for a Dryer, Relocating an Electric Dryer to Another Location, 3-Wire and 4-Wire Dryer Cords.
Wire a Dryer Outlet and Dryer Cord
Guide to Wiring for an Electric Dryer
Electrical Question: We have a GE Electric dryer (Model- DBLR333EEEWW) says inside door 120/240Volt 60hz and then under that 120/208V 60hz. It has the NEMA 10-30R 30AMP power cord already attached. I also purchased the three prong power outlet to install that fits this cord.
- We are planning to take this dryer to be used in a country where the electrical system is 220 volt 50hz.
- So the question is can we just install the three prong outlet into the 220 volt wall? I was told a while back that the dryer uses split current, one voltage to power heating element and another voltage to power fan or motor? Not sure if I am remembering correctly.
- What is the wiring detail of the 3 prong outlet exactly? What current or voltage wires go where?
- Could you also elaborate on the 30 amp double pole breaker, what exactly is it, where is it installed and what does it do? I did look at your wiring diagram for 220 volt outlets.
We will be installing this ourselves, if it is even possible, so any advice you can give will greatly appreciated.
Thanks much Dave!
This electrical wiring question came from: Sal, from Scottsdale, Arizona
Additional Comments: What a site you have! Its wonderful you are here to help us with your electrical expertise. I am going to share your site with everyone. Thanks for being here.
Thanks for your electrical wiring question Sal.
How to Wire an Electric Dryer Circuit and Dryer Cord
- Application: Wiring a 240volt electric dryer.
- Skill Level: Intermediate to Advanced – Best performed by a Licensed Electrician.
- Tools Required: Basic Electricians Pouch Hand Tools, electric drill, auger bits and extension cord.
- Estimated Time: Depends on personal level experience, ability to work with tools and install electrical circuit wiring.
- Notice: Installing an additional dryer circuit should be done according to local and national electrical codes with a permit and be inspected.
- Dedicated Electric Circuit for a Dryer
- The circuit wiring for an electric dryer consists of 3 insulated wires, two hots, a dedicated neutral and a ground wire.
- Depending on the age of the dryer and the type of cord the neutral wire may or may not be connected, this depends on weather there will be a 3-wire or 4-wire receptacle for the dryer cord.
- The 2-pole circuit breaker provides two circuits consisting of 120 volts each, however when the voltage is tested from these two circuits the result will be 220 to 240 volts.
- Testing each individual circuit to ground or the neutral the reading will be 110 to 120 volts. The electric heating elements of the dryer require 240 volts and the timer and control circuit typically operate on 120 volts.
- The specific voltage and power requirements will be clearly identified on the label which is typically found on the door jam and may be read when the door is open.
- Each individual electric component including the electric motor should have the voltage specifically identified, however all of these components are pre-wired internally, so the dryer cord is the only main connection that needs to be installed.
- Relocating an Electric Dryer to Another Location
- Moving an Electric Dryer to Another Country with 50hz or 60hz Power
- Unless the electric dryer specifically states that it is approved to operate in the country it is being moved to and the electrical voltage and hertz or cycles is compatible then I would highly recommend selling the dryer before you leave and purchase one in the country you will be moving to.
- Incorrect voltage or hertz will cause the dryer electrical components to overheat and burn out. If the brand name for the dryer is not commonly found in the country you will have a hard time getting a service technician.
- Some voltage or power converters may be available however you are still taking a risk of burning out an electric component prematurely and then you will require dryer repair service.
See More about Wiring an Electric Dryer
3-Wire and 4-Wire Dryer Cords
- See an electric dryer installation with a typical 220 Volt electric power cord wiring system. You may find yourself with either a 3-wire or 4-wire electric dryer, or a 3-wire or 4-wire outlet. Lets look a how the electric dryer is wired and what to do if your cord does not match the plug.
Wiring 220 Volt Electrical Outlet
- Home electrical wiring includes 110 volt outlets and 220 volt outlets and receptacles which are common place in every home. See how electrical outlets for the home are wired.
Home Electrical Circuit Breakers
Home Electrical Circuit Breakers
A guide to home electrical circuit breakers and how they work to protect your electrical wiring. When properly installed, your home electrical wiring is protected by a circuit protection device.
Electrical Wire for the Home
Complete listing of electrical wire types and parts used for home projects with electrical code information serves as selection guidelines.
The following may also be helpful for you:
Learn more about Home Electrical Wiring
Be Careful and Be Safe - Never Work on Energized Circuits!
Consult your Local Building Department about Permits and Inspections for all Electric Wiring Projects.
The Safest Way to Test Electrical Devices and Identify Electric Wires!The Non-Contact Electrical Tester
This is a testing tool that I have had in my personal electrical tool pouch for years, and is the first test tool I grab to help identify electrical wiring. It is a Non-contact tester that I use to easily Detect Voltage in Cables, Cords, Circuit Breakers, Lighting Fixtures, Switches, Outlets and Wires. Simply insert the end of the tester into an outlet, lamp socket, or hold the end of the tester against the wire you wish to test. Very handy and easy to use.
The Quickest Way to Check for Faulty Electrical Wiring!The Plug-In Outlet Tester
This is the first tool I grab to troubleshoot a problem with outlet circuit wiring. This popular tester is also used by most inspectors to test for power and check the polarity of circuit wiring.
It detects probable improper wiring conditions in standard 110-125 VAC outlets Provides 6 probable wiring conditions that are quick and easy to read for ultimate efficiency Lights indicate if wiring is correct and indicator light chart is included Tests standard 3-wire outlets UL Listed Light indicates if wiring is incorrect Very handy and easy to use.
Strip Off Wire Insulation without Nicking and Damaging the Electric Wire!The Wire Stripper and Wire Cutter
My absolute favorite wire stripping tool that I have had in my personal electrical tool pouch for years, and this is the tool I use to safely strip electrical wires.
This handy tool has multiple uses:
The wire gauges are shown on the side of the tool so you know which slot to use for stripping insulation.
The end of the tool can be used to grip and bend wire which is handy for attaching wire onto the screw terminals of switches and outlets..
The wire stripper will work on both solid and stranded wire. This tool is Very Handy and Easy to Use.
|More articles about Dryer Circuit, Electrical Wiring and Home Electrical Wiring:|
|« Previous||Next »|
|How to Install Wiring for a Stack Washer and Dryer||Avoid Home Improvement Electrical Wiring Problems|
SO IT WOULD BE BEST TO INSTALL A NEW CIRCUIT – IS THAT RIGHT?
YES – THAT IS CORRECT!