Wiring Master and Slave Switches
|
How to Wire Master and Slave Switches for Three and Four Switch Lighting Control: I need 4-way wiring diagram using master dimmer & companion dimmer & 1 4-Way rocker switch. |
Master and Slave Switches are Great for Multiple Switch Locations
[ad#block]Electrical Question: I need 4-way wiring diagram using master dimmer & companion dimmer & 1 4-Way rocker switch. I will try to send picture.
This electrical question came from: Barry, a Homeowner from Lakeland, TN
Dave’s Reply:
Thanks for your electrical question Barry.
How to Wire Master and Slave Switches for Three and Four Switches
- The Master and Slave switch and dimmer switch combo’s are a great way to control lighting from several locations.
- The key is to have compatible switches of the same brand. Typically these switches may be purchase in pairs.
- The wiring is wiring is very straight forward and may be slightly different depending on the actual switches that you buy. 120 Volt, or line voltage switches are most common for typical 120 volt light fixtures.
- Low volt lighting may require specific switches when dimmer controls are to be used.
- Additional options include RF switches from manufacturers which are available at most hardware stores or your local electrical wholesale distributor such as Rexel.
More about Wiring Light Switches
Checking Light Fixture Wiring Connections
I am wiring 3 12V 50W halogen pendant lights over my bar. They will all be controlled by a single switch Continue reading
wiring a dimmer switch
3 Way Dimmer Switch Wiring Diagram
Fully explained 3 way dimmer switch wiring diagram will take the mystery out of wiring a 3-way dimmer switch.
The following may also be helpful for you:
|
||||||||
Be Careful and Be Safe - Never Work on Energized Circuits!
Consult your Local Building Department about Permits and Inspections for all Electric Wiring Projects.
The Safest Way to Test Electrical Devices and Identify Electric Wires!The Non-Contact Electrical TesterThis is a testing tool that I have had in my personal electrical tool pouch for years, and is the first test tool I grab to help identify electrical wiring. It is a Non-contact tester that I use to easily Detect Voltage in Cables, Cords, Circuit Breakers, Lighting Fixtures, Switches, Outlets and Wires. Simply insert the end of the tester into an outlet, lamp socket, or hold the end of the tester against the wire you wish to test. Very handy and easy to use.
The Quickest Way to Check for Faulty Electrical Wiring!The Plug-In Outlet TesterThis is the first tool I grab to troubleshoot a problem with outlet circuit wiring. This popular tester is also used by most inspectors to test for power and check the polarity of circuit wiring. It detects probable improper wiring conditions in standard 110-125 VAC outlets Provides 6 probable wiring conditions that are quick and easy to read for ultimate efficiency Lights indicate if wiring is correct and indicator light chart is included Tests standard 3-wire outlets UL Listed Light indicates if wiring is incorrect Very handy and easy to use.
Strip Off Wire Insulation without Nicking and Damaging the Electric Wire!The Wire Stripper and Wire CutterMy absolute favorite wire stripping tool that I have had in my personal electrical tool pouch for years, and this is the tool I use to safely strip electrical wires. This handy tool has multiple uses: The wire gauges are shown on the side of the tool so you know which slot to use for stripping insulation. The end of the tool can be used to grip and bend wire which is handy for attaching wire onto the screw terminals of switches and outlets.. The wire stripper will work on both solid and stranded wire. This tool is Very Handy and Easy to Use. |
||
| More articles about 4-Way Switch, Lighting and Home Electrical Wiring: | |
| « Previous | Next » |
| Wiring a GFCI Receptacle | Testing Circuits and Circuit Breakers |
Sir we are using two compressors, I need to connect the two compressors as a redundant configuration, so if the 1st is faulty then only I need to turn on the second compressor. Please send me a solution
Hi Jinsen,
Install a Double Throw Switch, which is like a transfer switch. This way one circuit could be switched to either compressor. The number of Poles of the Double Throw switch would depend on the Voltage and Phase of the circuit, such as DPDT for 240 Volt Single Phase Circuit.
Dave