How to Solve Light Fixture and Switch Wiring Problems
How do I fix a problem with a light that I am trying to install? Wiring Connections for Light Fixtures and Switches.
Wiring Light Fixtures and Switches
Electrical Question: How do I fix a problem with a light I am trying to install?
- I have a problem with a light I am trying to install in my kitchen.
- The light was originally a fluorescent light but I replaced it with a regular 2 bulb ceiling mount light fixture.
- There are two cables in the ceiling, (black, white and ground wires in each) one is connected to the kitchen light switch and the second cable is coming from an outlet with a motion sensor outdoor light that is always switched on. Both were originally connected to the fluorescent light.
- I cannot get the light fixture, or the outside light working. I tried wiring all blacks (4 wires) all whites (4 wires) and all grounds (3 wires) together-(3 bundles) I have also tried the two black from the light wired to one black and the two white from the light to the other black with the two external white wires together and all three grounds together-(4 bundles).
- It seems like this is a complicated lighting schematic where both light fixtures are getting power from the same source and they need to be wired in parallel.
Not sure what to try next, any help would be greatly appreciated!
This electrical wiring question came from: Andy, a Student in New York.
Thanks for your electrical wiring question Andy.
How to Wire Light Switches and Occupancy Sensors
Application: Troubleshooting and Testing Light Switch Wiring.
Skill Level: Intermediate to Advanced. This electrical project is best performed by a licensed electrical contractor.
Tools Required: Basic Electricians Pouch Hand Tools and a Voltage Tester.
Estimated Time: Depends on personal level experience, ability to work with hand tools and electrical troubleshooting skills.
Precaution: Identify the circuit, turn it OFF and then Tag it with a Note before performing any wiring or inspections.
Wiring Connections for Light Fixtures and Switches
- Identify the Power Source for the Light Fixture
- Using my voltage tester, I would carefully identify the power source, making sure that I test the hot to ground and the same hot to neutral.
- This is done one cable at a time, and one wire at a time.
- Once the power source is identified I would identify the power source cable with black electrical tape, and cap off the wires using orange or yellow wire nuts.
- Wiring Light Switches
- Next, the wiring to the switches will need to be identified starting by looking at the wiring on the switch so I can see which wires are actually connected to the switch.
- Then using the ohms scale on my meter or my continuity tester I would test each remaining cable to identify the cable that goes to each switch.
- I will notice that there are fewer cables left and where they are going is beginning to make since.
- Wiring a Switch for Two or More Light Fixtures
- Because the power source is shared with the two light fixtures, then I understand that the white neutral wire of the power source cable will be connected to the neutral wires of each light fixture.
- Wiring from a Shared Power Source
- The black wire of the power source will connect to one of the wires leading to the light switch, and the return wire from the light switch will connect to the kitchen light fixture.
- Because the outside motion light is hot all the time, then it will connect to the black wire of the power source cable.
- Bonding the Ground Wire
- All of the earth ground wires are connected together using a wire connector.
- Additional ground wires are added to this group of ground wires to provide bonding all of the components of the circuit as follows:
- Light fixtures
- Light switches
- Junction box
- NOTE: Bond the earth ground to these components using Green Grounding Screws and or Bare Copper Wire or Green insulated wire.
More about Wiring Light Fixtures and Light Switches
Light Switch Wiring
Wiring a Light Switch – Diagram 1
Fully explained pictures and wiring diagrams about wiring light switches describing the most common switches starting with photo diagram 1.
Home Lighting Articles
Home Lighting Articles covering recessed lighting, under cabinet lighting, lighting terminology and more.
How to Install Kitchen Electrical Wiring
Kitchen Electrical Wiring
Fully Explained Photos and Wiring Diagrams for Kitchen Electrical Wiring with Code Requirements for most new or remodel projects.
The following may also be helpful for you:
Learn more about Home Electrical Wiring
Be Careful and Be Safe - Never Work on Energized Circuits!
Consult your Local Building Department about Permits and Inspections for all Electric Wiring Projects.
The Safest Way to Test Electrical Devices and Identify Electric Wires!The Non-Contact Electrical Tester
This is a testing tool that I have had in my personal electrical tool pouch for years, and is the first test tool I grab to help identify electrical wiring. It is a Non-contact tester that I use to easily Detect Voltage in Cables, Cords, Circuit Breakers, Lighting Fixtures, Switches, Outlets and Wires. Simply insert the end of the tester into an outlet, lamp socket, or hold the end of the tester against the wire you wish to test. Very handy and easy to use.
The Quickest Way to Check for Faulty Electrical Wiring!The Plug-In Outlet Tester
This is the first tool I grab to troubleshoot a problem with outlet circuit wiring. This popular tester is also used by most inspectors to test for power and check the polarity of circuit wiring.
It detects probable improper wiring conditions in standard 110-125 VAC outlets Provides 6 probable wiring conditions that are quick and easy to read for ultimate efficiency Lights indicate if wiring is correct and indicator light chart is included Tests standard 3-wire outlets UL Listed Light indicates if wiring is incorrect Very handy and easy to use.
Strip Off Wire Insulation without Nicking and Damaging the Electric Wire!The Wire Stripper and Wire Cutter
My absolute favorite wire stripping tool that I have had in my personal electrical tool pouch for years, and this is the tool I use to safely strip electrical wires.
This handy tool has multiple uses:
The wire gauges are shown on the side of the tool so you know which slot to use for stripping insulation.
The end of the tool can be used to grip and bend wire which is handy for attaching wire onto the screw terminals of switches and outlets..
The wire stripper will work on both solid and stranded wire. This tool is Very Handy and Easy to Use.
|More articles about Electrical Wiring, Light Switch Wiring and Home Electrical Wiring:|
|« Previous||Next »|
|Upgrading Home Electrical Wiring||Incorrect Outlet Ground Wire Could be a Shock Hazard|
I am trying to install a ceiling fan with a light. I have 4 wire bundles which are for the outside light, inside light, and a dimmer switch. In the ceiling there are 4 black, 4 white, 4 bare wires how do I connect 2 black have power?
When there are several cables and wires we typically use a voltage tester to identify the wiring. Keep in mind that the wiring may be used for the following purpose: The incoming power source, wiring to or from a wall switch, and wiring leading to the other light fixtures or outlets in the general area. In some cases when the wiring configuration is unknown it is helpful to use a continuity tester with the circuit power turned off. This will help us to help identify lights, switches, wall outlets, and other electrical devices which may be connected to the junction box wiring.
Thank you for sharing your electrical question with us,