How Much Will an Electrician Charge to Install a New Circuit
How much would an electrician charge to install circuit wiring? The Basic Cost Involved for Adding Electrical Wiring.
Hiring an Electrician to Install a New Circuit
Electrical Question: How much would an electrician charge to install new circuit wiring?
My electrical wiring project involves Changing the Existing Wiring, and Adding a Circuit from my Panel to the Attic of a Old Home.
- My house is 20 yr old. There is a circuit on the 2nd floor of my home that goes out more often than not. I think it’s because it’s overload by additions to the circuit by the previous owner (ceilings fans, lights,etc.) The circuit is run through the attic.
- The main panel is in the basement, which is not finished. If I were to have a professional replace the wires of that circuit and add a new circuit to spread the load, how long should I expect this to take? I am asking because I want to know what I should expect to pay since most electricians charge by the hour. Thanks.
This electrical wiring question came from Mindy, a Homeowner in Maryland.
Thanks for your electrical wiring question Mindy.
Adding a New Electrical Circuit
Application: Install New Circuit the Wiring from a Panel to the Attic.
Skill Level: Intermediate to Advanced. This electrical wiring project is best performed by a Licensed Electrical Contractor or Certified Electrician.
Electrical Tools Required: Basic Electricians Pouch Hand Tools, Voltage Tester, and appropriate Safety Gear.
Estimated Time: Depends on the personal level experience, ability to work with tools, install electrical circuit wiring, and the available access to the project area.
Electrical Safety: Identify the electrical power source to the Panel, turn it OFF and Tag with a Note before working with the electrical wiring.
Electrical Wiring Parts and Materials: Electrical parts and materials for the Panel should be approved for the specific project and compliant with local and national electrical codes.
Electrical Codes and Inspections: Installing or changing home electrical wiring should be done according to local and national electrical codes as adopted in Maryland. A permit and inspections may also be required.
The Basic Cost for Adding Electrical Wiring for a New Circuit
This electrical wiring project is about Adding New Electrical Wiring from a Panel to the Attic of a Old Home.
This example will demonstrate How an Electrician will Install Electrical Wiring for a New Dedicated Circuit to an Attic.
How Much an Electrician Charges
Typically, an electrician will charge for their Time and the Materials needed for the project. When adding and changing the existing wiring a permit may be required, therefore permit fees will apply. The hourly charge for an electrician will depend on the going rate in your area.
Get Multiple Bids or Quotations
It may be wise to consider getting at least three quotations from separate electrical contractors, and asking for credentials and customer referrals is very important.
How Long will it Take?
The estimated time it takes to do this project will depend on the available access to the project areas, such as attic and basement access and the available room to perform the work.
What the Electrician will do When Installing a New Dedicated Circuit
Determining the Circuit Size
The size of the electrical circuit the will depend on the existing overloaded condition. In this example, an additional 120volt circuit would be required. The wire type or electrical cable type is determined by the type of structure and if the wiring will be enclosed inside a wall, or if the wiring will be protected by electrical conduit.
Selecting the Electrical Cable Factors for determining cable type include where the cable will be routed or installed, such as through a basement, crawl space or attic, etc.
The Electrical Junction Boxes
The same is true for the junction boxes that will be selected for the circuit that will be installed. For example, will the junction box be surface mounted or flush mounted. The type of junction box is determined by the location of the installation, and the size of the circuit cable.
Splitting the existing circuit wires over to the new circuit will require circuit tracing and identification for the right connections to the new electrical junction box.
Connecting the Circuit Wiring
The circuit wires and ground wires are spliced together and bonded to the new junction box using the appropriately sized wire connectors. The newly installed circuit wiring components will be fastened and secured and protected as required.
Code compliance for electrical wiring installed to an attic is very important.
The electrical components of the circuit must be fully compatible and have the correct rated capacity.
More about Hiring an Electrician
Checklist for Hiring a Electrician:
Avoid problems with your home improvement electrical project by hiring the right person for the job. This checklist will help you make sure that your contractor measures up.
More about Wiring an Electrical Circuit
House Wiring Circuits and Circuit Breakers
This article looks at common 120 volt and 240 volt house wiring circuits and the circuit breakers that are installed identifying the types and amperage sizes used in most homes.
Electrical Panel Circuit Listing
Electrical Wire for the Home
Complete listing of electrical wire types and parts used for home projects with electrical code information serves as selection guidelines.
How to Install Basement Electrical Wiring
Basement Electrical Wiring
Fully Explained Photos and Wiring Diagrams for Basement Electrical Wiring with Code Requirements for most new or remodel projects.
The following may also be helpful for you:
Be Careful and Be Safe - Never Work on Energized Circuits!
Consult your Local Building Department about Permits and Inspections for all Electric Wiring Projects.
The Safest Way to Test Electrical Devices and Identify Electric Wires!The Non-Contact Electrical Tester
This is a testing tool that I have had in my personal electrical tool pouch for years, and is the first test tool I grab to help identify electrical wiring. It is a Non-contact tester that I use to easily Detect Voltage in Cables, Cords, Circuit Breakers, Lighting Fixtures, Switches, Outlets and Wires. Simply insert the end of the tester into an outlet, lamp socket, or hold the end of the tester against the wire you wish to test. Very handy and easy to use.
The Quickest Way to Check for Faulty Electrical Wiring!The Plug-In Outlet Tester
This is the first tool I grab to troubleshoot a problem with outlet circuit wiring. This popular tester is also used by most inspectors to test for power and check the polarity of circuit wiring.
It detects probable improper wiring conditions in standard 110-125 VAC outlets Provides 6 probable wiring conditions that are quick and easy to read for ultimate efficiency Lights indicate if wiring is correct and indicator light chart is included Tests standard 3-wire outlets UL Listed Light indicates if wiring is incorrect Very handy and easy to use.
Strip Off Wire Insulation without Nicking and Damaging the Electric Wire!The Wire Stripper and Wire Cutter
My absolute favorite wire stripping tool that I have had in my personal electrical tool pouch for years, and this is the tool I use to safely strip electrical wires.
This handy tool has multiple uses:
The wire gauges are shown on the side of the tool so you know which slot to use for stripping insulation.
The end of the tool can be used to grip and bend wire which is handy for attaching wire onto the screw terminals of switches and outlets..
The wire stripper will work on both solid and stranded wire. This tool is Very Handy and Easy to Use.
|More articles about Electrical Wiring and Home Electrical Wiring:|
|« Previous||Next »|
|Are You Doing Your Electrical Wiring Project Right?||How to Wire a Switch for a New Light Fixture|