Electric Water Heater Wiring Connections
How are the electrical wires connected for an electric water heater? Wiring Connections for a 240 volt 30 amp Electric Water Heater.
Wiring a Water Heater
Electrical Question: How are the electrical wires connected for an electric water heater?
I want to install a new electric water heater on a double breaker – two pole 30 AMP circuit that previously fed an electric dryer which is now discarded.
- The wire type is labeled 10-3 AWG copper.
- The wire colors are black, red and white.
- How should these wires be connected to the wiring on the water heater?
This water heater question came from: Linus, from Port Royal, Pennsylvania.
Thanks for your electric water heater question Linus.
How to Wire a Water Heater
Application: Wiring a 240Volt Electric Water Heater.
Skill Level: Intermediate to Advanced – Best wired by a Certified Electrician, Licensed Electrical Contractor, or Installed by a Licensed Plumbing Contractor.
Tools Required: Basic Electricians Pouch Hand Tools, Voltage Tester.
Estimated Time: Depends on personal level experience, ability to work with tools and install 240 volt electrical circuit wiring.
Precaution: Identify the water heater circuit in the panel, turn it OFF and Tag it with a Note before working with the wiring connections.
Notice: Installing an additional 240 volt water heater circuit should be done according to local and national electrical codes with a permit and be inspected.
- Electric Water Heater Connections
Linus, the typical electric water heater requires a dedicated 30 amp 240 volt circuit, and making use of the dryer circuit which is not used is OK to do, however as you discovered the dryer circuit has a dedicated neutral wire which is not required for your electric water heater, so in a case such as this here are the connections:
- Wiring Connections for a 240 volt 30 amp Electric Water Heater
- The ground wire of the circuit is fastened to the provided green ground screw which is found in the wire connection junction box.
- The white neutral wire is just capped off with a wire connector or electrical tape.
- The Red Wire of the circuit connects to the red wire of the water heater.
- The Black Wire of the circuit connects to the Black wire of the water heater.
- Connecting the Wire of a Water Heater
- If your water heater has two black lead wires it really does not matter which connection of the red wire and black wire connects to the water heater leads.
- Support any flexible conduit and provide proper connection fittings.
- Install the cover plate over the water heater wiring connection junction box.
- As always, positively identify the circuit and make sure the circuit is off before making any connections, and be sure to relabel the circuit breaker to show that it is now being used for the water heater.
- Install a Water Heater Time Clock Energy Savings Option
- Consider installing a Water Heater Time Clock which will enable you to control the water heater so that it is not On all the time.
- A suggested schedule would be to have it turn OFF at bedtime and turning back ON one hour before you normally get up. this will save a considerable amount of energy.
More about Wiring a Water Heater
Electrical Circuit Wiring
This article looks at common 120 volt and 240 volt house wiring circuits and the circuit breakers that are installed identifying the types and amperage sizes used in most homes.
Home Electrical Circuit Breakers
The following may also be helpful for you:
Be Careful and Be Safe - Never Work on Energized Circuits!
Consult your Local Building Department about Permits and Inspections for all Electric Wiring Projects.
The Safest Way to Test Electrical Devices and Identify Electric Wires!The Non-Contact Electrical Tester
This is a testing tool that I have had in my personal electrical tool pouch for years, and is the first test tool I grab to help identify electrical wiring. It is a Non-contact tester that I use to easily Detect Voltage in Cables, Cords, Circuit Breakers, Lighting Fixtures, Switches, Outlets and Wires. Simply insert the end of the tester into an outlet, lamp socket, or hold the end of the tester against the wire you wish to test. Very handy and easy to use.
The Quickest Way to Check for Faulty Electrical Wiring!The Plug-In Outlet Tester
This is the first tool I grab to troubleshoot a problem with outlet circuit wiring. This popular tester is also used by most inspectors to test for power and check the polarity of circuit wiring.
It detects probable improper wiring conditions in standard 110-125 VAC outlets Provides 6 probable wiring conditions that are quick and easy to read for ultimate efficiency Lights indicate if wiring is correct and indicator light chart is included Tests standard 3-wire outlets UL Listed Light indicates if wiring is incorrect Very handy and easy to use.
Strip Off Wire Insulation without Nicking and Damaging the Electric Wire!The Wire Stripper and Wire Cutter
My absolute favorite wire stripping tool that I have had in my personal electrical tool pouch for years, and this is the tool I use to safely strip electrical wires.
This handy tool has multiple uses:
The wire gauges are shown on the side of the tool so you know which slot to use for stripping insulation.
The end of the tool can be used to grip and bend wire which is handy for attaching wire onto the screw terminals of switches and outlets..
The wire stripper will work on both solid and stranded wire. This tool is Very Handy and Easy to Use.
|More articles about Electric Wiring, Water Heater and Home Electrical Wiring:|
|« Previous||Next »|
|Electrical Circuit Requirements for Kitchen Ovens||Where Can I Find 14Gauge Glass Wrapped Wiring?|